[求助]谁给看看老是调试不成功
<p><font face="Verdana">;;;---------------------<br/>;;;插入爆破材料库<br/>;;;---------------------<br/>(DEFUN C:bpclk() (SETQ DCL_ID (LOAD_DIALOG "custom.DCL"))<br/>(NEW_DIALOG "BP_DCL" DCL_ID)<br/> (setq bt2t (GET_TILE "bp_2t")<br/> bp4t (GET_TILE "bp_4t")<br/> bp6t (GET_TILE "bp_6t")<br/> )<br/> <br/> (cond (= bp2t 1) (setq bpnm "bp2t.dwg")<br/> (= bp4t 1) (setq bpnm "bp4t.dwg")<br/> (= bp6t 1) (setq bpnm "bp6t.dwg")<br/> )<br/>(ACTION_TILE "accept" "(drw_bp)(done_dialog)")<br/>(START_DIALOG)(UNLOAD_DIALOG DCL_ID)<br/>(PRINC))</font></p><p><font face="Verdana">(defun drw_bp()<br/> (setq pt1 (getpoint "插入点<炸药出口>:"))<br/> (setq pt2 (getpoint "巷道方向:"))<br/> (setq fwj (angle pt1 pt2))<br/> (setvar "aunits" 3);;角度弧度<br/> (setq M (get_m));;获取比例m<br/> (command "insert" bpnm pt1 1 "" fwj);插入汇签<br/> );;;end插入爆破材料库<br/></p>
<p><font face="Verdana">//------------------------<br/>//插入爆破材料库对话框<br/>//---------------------<br/>BP_DCL:dialog<br/>{ label="插入爆破材料库";<br/> :radio_row<br/> {label="";<br/> :radio_button<br/> {label="1～2t";<br/> key="bp_2t";<br/> value=1;<br/> }</font></p>
<p><font face="Verdana"> :radio_button<br/> {label="3～4t";<br/> key="bp_4t";<br/> value=0;<br/> }<br/> :radio_button<br/> {label="5～6t";<br/> key="bp_6t";<br/> value=0;<br/> }<br/> }<br/> ok_cancel;<br/> }</font></p></font> (setq M (get_m));;获取比例m可以去掉 <p>程序散乱，不好读。</p>
<p>简单看了下有下列问题：</p>
<p>1、cond函数后的程序结构有误，每个判断要加一对圆括弧。</p>
<p>2、在done_dislog前的函数中不能调用command。</p>
<p>3、对话框文件名是ddd.dcl，可程序中怎么用<font face="Verdana">custom.DCL</font>加载？</p> 本帖最后由 作者 于 2010-6-22 23:00:20 编辑 <br /><br /> 回楼zzxxqq，ddd是因为我另存为时临时起的名字，<font face="Verdana"><br/>(ACTION_TILE "accept" "(drw_bp)(done_dialog)")<br/>(command "insert" bpnm pt1 1 "" fwj);插入汇签<br/>(START_DIALOG)(UNLOAD_DIALOG DCL_ID)<br/>这样可以吗<br/><br/></font> DEFUN C:bpclk<br/> (if (> (SETQ DCL_ID (LOAD_DIALOG "custom.DCL")) 0) (progn<br/> (if (NEW_DIALOG "BP_DCL" DCL_ID) (progn<br/> (getdata)<br/> (ACTION_TILE "accept" "(getdata)(done_dialog 1)")<br/> (action_tile "cancel" "(done_dialog 0)")<br/> (setq re (START_DIALOG))<br/> )<br/> (alert "无法显示对话框！")<br/> )<br/> (UNLOAD_DIALOG DCL_ID)<br/> )<br/> (alert "无法加载对话框！")<br/> )<br/> (if (= re 1) (drw_bp))<br/> (PRINC)<br/>)<br/>(defun getdata ()<br/> (setq bt2t (GET_TILE "bp_2t")<br/> bp4t (GET_TILE "bp_4t")<br/> bp6t (GET_TILE "bp_6t"))<br/> (cond<br/> ((= bp2t 1) (setq bpnm "bp2t.dwg"))<br/> ((= bp4t 1) (setq bpnm "bp4t.dwg"))<br/> ((= bp6t 1) (setq bpnm "bp6t.dwg"))<br/> )<br/>)<br/>(defun drw_bp()<br/> (setq pt1 (getpoint "插入点<炸药出口>:"))<br/> (setq pt2 (getpoint "巷道方向:"))<br/> (setq fwj (angle pt1 pt2))<br/> (setvar "aunits" 3);;角度弧度<br/> (setq M (get_m));;获取比例m<br/> (command "insert" bpnm pt1 1 "" fwj);插入汇签<br/>);;;end插入爆破材料库
页:
[1]